Sheetplan support
Email support@whitehatharbor.com with "Sheetplan" in the subject. I answer myself, Monday to Friday, 9:00 to 17:00 US Eastern time, with a first reply within 2 business days.
It helps to say which phone you use (iPhone or Android, and the system version), what you tapped, and what you expected to happen. If a plan looks wrong, list the stock and parts you typed, or send the printed plan. In the app, Settings (the gear on the home screen), then Contact support, opens an email to me.
Getting the numbers right
What is kerf, and what should I enter?
Kerf is the width of wood the blade turns into sawdust at every cut. Most full-kerf table-saw blades are 1/8" (about 3 mm); thin-kerf blades are about 3/32"; track saws and circular saws vary. The blade's packaging usually says, or cut a scrap and measure the slot. New projects start at 1/8" (3 mm in millimetre mode). Enter it under Saw and material in the project.
What does trim do?
For sheets, Trim each edge takes that much off all four edges first, for chipped or out-of-square factory edges. For boards, Trim each end takes it off both ends, for rough or checked ends. Leave it at 0 if your stock is clean.
How do I type lengths?
The way you'd say them: 23-5/8, 23 5/8, 23.625, 5/8, 2' 6" or 8 ft. In millimetre mode a plain number is millimetres, 61 cm and 0.61 m work, and a number with an inch mark or a fraction is read as inches. Lengths are shown rounded to 1/16" by default; change it to 1/8, 1/32 or 1/64 in Settings. Switching a project between inches and millimetres converts every size in it.
How does grain work?
On a sheet with a grain, a part marked Grain keeps its length along the length of the sheet (the 96" or 2440 mm side), so the grain runs the way you want on the finished piece. Parts without it may be turned to fit better. For MDF, melamine or anything without a grain, turn off Sheet has a grain and every part may turn.
What does "On hand" mean?
How many of that board or sheet you already have. Leave it empty to buy as many as needed. If you set it and the parts don't fit, the plan says which parts are left out.
Reading the plan
How do I follow the cut sequence?
Each sheet's steps are in order: "Rip" is a cut along the length of the panel, "Crosscut" is a cut across it, and each step names the panel it comes off, so you can measure from the edge of the piece in front of you. Every cut goes straight through the panel, as a table saw, track saw or panel saw makes it. Parts are lettered on the drawing and in the cut list.
Why is there so much waste?
The waste counts the kerf, the trim and every offcut, including the unused end of the last sheet or board, which you'll usually keep. A small project on one sheet can show 30% waste and still be the best you can do with whole sheets. The plan shows the biggest offcut so you can judge what's left. For boards, "Least wood possible for these cuts" means no plan could use fewer boards of that length.
A part is "left out". Why?
Either it's bigger than any board or sheet you listed (after the trim), or you set an On hand count that runs out. For a grain-locked part, try unlocking its grain if the grain direction doesn't matter, or add a bigger stock size.
Pro features
How do I print the plan?
Open a plan and tap Share the PDF. The PDF has the summary, the cut list, every layout and the steps; turn on Include part labels to add a page of labels, one per piece with its letter, size and sheet or board. Send it to a printer, save it to Files, or message it to yourself.
How do material cost and edge banding work?
Type a Price each on each board or sheet size; the plan adds up the ones you need to buy. For edge banding, tap Edge banding on a part and pick how many long and short edges get banding; the plan adds up the length over every piece. Buy a little extra for trimming.
Pro and purchases
I bought Pro but the app shows the free version
Open Settings and tap Restore purchases, signed in to the same Apple ID or Google account you bought with. The Pro screen has the same button. If Pro still doesn't show, email me with the order id from your App Store or Google Play receipt.
Is there a subscription to cancel?
No. Pro is one payment and nothing renews.
How do I get a refund?
App Store purchases are refunded by Apple: request one at reportaproblem.apple.com. On Google Play you can request one in the Play Store within 48 hours; after that, email me with the order id. The terms have the details.
Your data
Where are my projects stored?
Only on your device, in the app's own storage. There's no account and no server, so I can't see, recover or move them. Restoring your phone from its own backup (iCloud or Google) may bring them back; otherwise a new phone starts fresh, and Restore purchases brings Pro back.
How do I delete my data?
Open a project and tap Delete project, or delete the app. If you want your purchase record at RevenueCat deleted too, email me with your order id. The privacy policy explains what that record holds.